Organizer Dish with 2 Dividers Shiny Silicone Mold for Resin Crafting Key Tray Coin Dish Jewelry Holder Ring Dish Silicon Mould
$32.99
This listing is for a shiny silicone mold to create a beautiful rectangle shaped organizer dish with 3 compartments. Lots of unique possibilities with this dish. The organizing dish will be great to hold jewelry or whatever. The size of this dish is 6" x 2 3/8" and it's approximately 3/4" deep.
Please message us with any questions you may have regarding this mold.
**Please note this listing is for the silicone mold ONLY.
All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)
Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS
• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.
PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.
Please message us with any questions you may have regarding this mold.
**Please note this listing is for the silicone mold ONLY.
All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)
Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS
• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.
PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.