Teddy Bear Silicone Mold, Bear Mold, Baby Shower Mold, Teddy Bear Mold for Resin, 3D Mold, 3D Resin Molds, Ornament Mold
$22.00
This listing is for a Teddy Bear Silicone Mold. These adorable little bears are so cute. They are perfect for baby showers or really any occasion. The Teddy Bear is about 2 1/4" tall and approximately 1 1/2" wide.
Please note this mold comes with a split down the side for easy demolding. Use the rubber bands supplied to align and seal the split before pouring your resin.
This listing is for the silicone mold ONLY.
Please message us with any questions you may have regarding this mold.
All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)
Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fareheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS
DONT TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
Make sure the resin is fully. Uncured resin may rip the mold.
Please follow all safety precautions when using resin. It is very toxic.
Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
If you have further questions or concerns about your mold, please shoot me a message on Etsy and Ill get you taken care of.
PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.
Please note this mold comes with a split down the side for easy demolding. Use the rubber bands supplied to align and seal the split before pouring your resin.
This listing is for the silicone mold ONLY.
Please message us with any questions you may have regarding this mold.
All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)
Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fareheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS
DONT TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
Make sure the resin is fully. Uncured resin may rip the mold.
Please follow all safety precautions when using resin. It is very toxic.
Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
If you have further questions or concerns about your mold, please shoot me a message on Etsy and Ill get you taken care of.
PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.