Alphabet Mold | Full Reverse | Uppercase Alphabet Mold, Keychain Mold, Magnet Mold
$7.50 - $155.00
DIMENSIONS:
TALL: 1 1/2"
WIDTH: Varied Per Letter
DEEP: 3/8"
CAVITIES PER MOLD: 4
This listing is for an Uppercase Alphabet Mold. Each letter is sold separately and in a grouping of 4 of the same letter. This is perfect when you need to produce a lot for your business. These molds are great for keychains, magnets or anything else. You may notice that the letters are reversed in the mold, this is because when you demold them you want them to face the right way, with the shiny smooth side as the front.
Please message us with any questions you may have regarding this mold.
**Please note this listing is for the silicone mold ONLY.
All molds are handmade and inspected before shipping.
** Please note that the variation photo shows more then 1 letter in it due to photo limitations. Each letter is sold individually or as an entire set.
Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS
• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.
PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.
TALL: 1 1/2"
WIDTH: Varied Per Letter
DEEP: 3/8"
CAVITIES PER MOLD: 4
This listing is for an Uppercase Alphabet Mold. Each letter is sold separately and in a grouping of 4 of the same letter. This is perfect when you need to produce a lot for your business. These molds are great for keychains, magnets or anything else. You may notice that the letters are reversed in the mold, this is because when you demold them you want them to face the right way, with the shiny smooth side as the front.
Please message us with any questions you may have regarding this mold.
**Please note this listing is for the silicone mold ONLY.
All molds are handmade and inspected before shipping.
** Please note that the variation photo shows more then 1 letter in it due to photo limitations. Each letter is sold individually or as an entire set.
Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS
• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.
PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.